One of Cad Company's Best Engineered Products that make serious Cadders smile! Will accommodate all shaft rocker systems. Angled top with shallow 30's Cadillac v16 style fins for that classy look. Sold with mounting bolt kit.
$295.00, As Cast.

Also available powder coated with polished fins for an additional charge.

One of Cad Company's Best Engineered Products that make serious Cadders smile! Will accommodate all shaft rocker systems. Cast with raised Cadillac script. Sold with mounting bolt kit.
Now Only $295.00, As Cast.
Shown w/ optional polishing and engraving

Polishing or powder coating with the top of the lettering polished also available for an additional charge.

One of Cad Company's Best Engineered Products that make serious Cadders smile! Clearance humps to accommodate all common adjustable rocker systems. Deep 50s style raised fins and raised early Cadillac script. Sold with mounting bolt kit.
$295.00, As Cast.
Note: Fite '49-'67 Cadillac 331, 365, 390, and 429 engines. '68-up big block engines require an adapter.

Polishing or powder coating with the tops of the script and fins polished are also available for an additional charge.

New Cad Company cam bearing

Introducing the cure for the cam bearing blues
The Cad Company grooved cam bearings (pictured) are made to our specs by durabond. They incorperate a groove around the outside to allow oil to flow around the the second hole, which allows oil to enter the bearing on the loaded side, decreasing the chance of bearing failure due to high spring pressure. They also have an oil clearance closer to the middle of the factory spec, instead of tighter like the other off-the-shelf bearings, eliminating the need to clearance the bearings during assembly. If you have a problem with the cam bearings 'smearing', these bearings are the solution.
Fits all 472 / 500 / 425 / 368 engines. $95.

Perfect for swaps! You no longer have to hunt down the elusive original rear sump pan for your engine.
This oil pan fits most swaps, and is of similar design to our fabricated steel rear sump pans, bringing along the performance gains (20 HP and 30 Ft-Lbs on a mild built engine) and providing the necessary clearance for installation in non-Cadillac RWD bodies. A Great Deal at $375.

Standard replacement rear sump pickup tube. Looks, fits, and works ilke the original.
This Pickup tube/ screen assembly fits stock, aluminum, and PC 7.0 steel rear sump oil pans.
$95 imported.

Standard replacement rear sump pickup tube. Looks, fits, and works like the original.
This Pickup tube/ screen assembly fits stock, aluminum, and PC 7.0 steel rear sump oil pans.
$125 USA.

Standard replacement front sump pickup tube. Looks, fits, and works ilke the original.
This Pickup tube/ screen assembly fits stock front sump sump oil pans ('68-'76 non-Eldo).
$95 imported.

Standard replacement front sump pickup tube. Looks, fits, and works ilke the original.
This Pickup tube/ screen assembly fits front sump sump oil pans ('68-'76 non-Eldo).
$125 USA.

Billet Aluminum AC Bracket Set for installing the GM R4 compressor on your Cad for more carb/ intake/ hood clearance. This set is for all OE and aftermarket intake variations (except for a roots type blower).
$275 In Stock.

Replace that funky bent steel stocker with this beautiful creation!Designed to provide correct leverage, and allows removal of distributor without completely removing the clamp.
$40 And In Stock.

For the looks or just to replace a rusted out original.They come lightly polished.
A Bargain at Only $49.

Nothing special - but folks have been asking for 'just an oil pump gasket', so here it is, the same gasket supplied with our pumps.
In Stock at Only $5!

These trick billet aluminum crank and water pump pulleys are the finishing touch for the Cadder with everything! Add your favorite style billet PS Pump and Alternator pulleys, and AC compressor pulley covers, and really blow some minds!
$275/set

The low-buck deal for use with smaller performance cams to add a measure of reliability for those who do not need the strength and/or expense of our more elaborate shaft rocker systems. Comes with special length pushrods and mounting bolt kit, ready to bolt on.
$450.00.

One of Cad Company's Best Engineered Products that make serious Cadders smile! Will accommodate all shaft rocker systems. Sold with mounting bolt kit.
Now Only $255.00, As Cast.
Shown w/ optional polishing and engraving

Polishing, powder coating and CNC engraving also available for an additional charge.

Will accommodate all shaft rocker systems. Sold with mounting bolt kit.
Now Only $255.00, As Cast.
Shown w/ optional engraving

w/ chrome dipstick - $45
Also available polished for $69